- 您现在的位置：买卖IC网 > Sheet目录1214 > EVAL-ADE7878EBZ (Analog Devices Inc)BOARD EVAL FOR ADE7878
ADE7854/ADE7858/ADE7868/ADE7878
Sign of Reactive Power Calculation
summarizes the relationship between the phase difference between
the voltage and the current and the sign of the resulting reactive
power calculation.
The ADE7858 / ADE7868 / ADE7878 have sign detection circuitry
for reactive power calculations that can monitor the total reactive
Data Sheet
Both total and fundamental reactive energy accumulations are
always a signed operation. Negative energy is subtracted from
the reactive energy contents.
achieve the integration of the reactive power signal in two
stages (see Figure 71). The process is identical for both total and
fundamental reactive powers.
powers or the fundamental reactive powers. As described in the
mulation is executed in two stages. Every time a sign change is
detected in the energy accumulation at the end of the first stage,
that is, after the energy accumulated into the internal accumulator
reaches the VARTHR register threshold, a dedicated interrupt is
triggered. The sign of each phase reactive power can be read in
the PHSIGN register. Bit 7 (REVRPSEL) in the ACCMODE
register sets the type of reactive power being monitored. When
REVRPSEL is 0, the default value, the total reactive power is
monitored. When REVRPSEL is 1, then the fundamental
reactive power is monitored.
?
?
The first stage is conducted inside the DSP: every 125 μs
(8 kHz frequency), the instantaneous phase total reactive
or fundamental power is accumulated into an internal
register. When a threshold is reached, a pulse is generated
at the processor port and the threshold is subtracted from
the internal register. The sign of the energy in this moment
The second stage is performed outside the DSP and consists
in accumulating the pulses generated by the processor into
internal 32-bit accumulation registers. The content of these
registers is transferred to the var-hour registers (xVARHR and
PMAX × f s × 3600 × 10 n
V FS × I FS
Bits[12:10] (REVRPC, REVRPB, and REVRPA, respectively)
in the STATUS0 register are set when a sign change occurs in
the power selected by Bit 7 (REVRPSEL) in the ACCMODE
register.
Bits[6:4] (CVARSIGN, BVARSIGN, and AVARSIGN, respectively)
in the PHSIGN register are set simultaneously with the REVRPC,
REVRPB, and REVRPA bits. They indicate the sign of the reactive
power. When they are 0, the reactive power is positive. When
they are 1, the reactive power is negative.
Bit REVRPx of the STATUS0 register and Bit xVARSIGN in the
PHSIGN register refer to the reactive power of Phase x, the
power type being selected by Bit REVRPSEL in ACCMODE
register.
Setting Bits[12:10] in the MASK0 register enables the REVRPC,
REVRPB, and REVRPA interrupts, respectively. If enabled, the
IRQ0 pin is set low and the status bit is set to 1 whenever a change
of sign occurs. To find the phase that triggered the interrupt,
the PHSIGN register is read immediately after reading the
STATUS0 register. Next, the status bit is cleared and the IRQ0
pin is set to high by writing to the STATUS0 register with the
corresponding bit set to 1.
Table 18. Sign of Reactive Power Calculation
xFVARHR) when these registers are accessed. AVARHR,
BVARHR, CVARHR, AFWATTHR, BFWATTHR, and
CFWATTHR represent phase fundamental reactive powers.
this process. The VARTHR 48-bit signed register contains the
threshold and it is introduced by the user. It is common for both
total and fundamental phase reactive powers. Its value depends
on how much energy is assigned to one LSB of var-hour
registers. When a derivative of reactive energy (varh) of [10 n
varh], where n is an integer, is desired as one LSB of the
xVARHR register; then, the xVARTHR register can be computed
using the following equation:
VARTHR =
where:
PMAX = 33,516,139 = 0x1FF6A6B, the instantaneous power
computed when the ADC inputs are at full scale.
f S = 8 kHz, the frequency with which the DSP computes the
instantaneous power.
V FS , I FS are the rms values of phase voltages and currents when
the ADC inputs are at full scale.
The maximum value that may be written on the VARTHR
Φ 1
Between 0 to +180
Between ?180 to 0
Between 0 to +180
Between ?180 to 0
Integrator
Off
Off
On
On
Sign of Reactive Power
Positive
Negative
Positive
Negative
register is 2 47 ? 1. The minimum value is 0x0, but it is
recommended to write a number equal to or greater than
PMAX. Never use negative numbers.
VARTHR is a 48-bit register. As previously stated in the Voltage
Φ is defined as the phase angle of the voltage signal minus the current
1
signal; that is, Φ is positive if the load is inductive and negative if the load is
capacitive.
Reactive Energy Calculation
Reactive energy is defined as the integral of reactive power.
the WTHR register shown in Figure 69, VARTHR is accessed as
two 32-bit registers (VARTHR1 and VARTHR0), each having eight
MSBs padded with 0s.
Reactive Energy = ∫ q(t)dt
(36)
Rev. H | Page 54 of 100
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
EVAL-ADE7880EBZ
BOARD EVAL FOR ADE7880
EVAL-ADE7953EBZ
BOARD EVAL FOR ADE7953
EVAL-ADF4002EBZ1
BOARD EVAL FOR ADF4002
EVAL-ADG788EBZ
BOARD EVALUATION FOR ADG788
EVAL-ADM1021AEB
BOARD EVAL FOR ADM1021
EVAL-ADM1023EB
BOARD EVAL FOR ADM1023
EVAL-ADM1031EB
BOARD EVAL FOR ADM1031
EVAL-ADM1062TQEBZ
BOARD EVALUATION FOR ADM1062TQ
相关代理商/技术参数
EVAL-ADE7880EBZ
功能描述:BOARD EVAL FOR ADE7880 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:* 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 主要目的:电源管理，电池充电器 嵌入式:否 已用 IC / 零件:MAX8903A 主要属性:1 芯锂离子电池 次要属性:状态 LED 已供物品:板
EVAL-ADE7880EBZ
制造商:Analog Devices 功能描述:ADE7880, ENERGY METER, 3 PH, SPI, I2C, E
EVAL-ADE7913EBZ
制造商:AD 制造商全称:Analog Devices 功能描述:3-Channel, Isolated, Sigma-Delta ADC with SPI
EVAL-ADE7953EBZ
功能描述:BOARD EVAL FOR ADE7953 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PSoC® 主要目的:电源管理，热管理 嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板，CD，电源
EVAL-ADF4001EBZ2
制造商:Analog Devices 功能描述:Evaluation Board For Pll Frequency Synthesizer 制造商:Analog Devices 功能描述:ADF4001 PLL SYNTHESIZER EVAL BOARD
EVAL-ADF4002EB1
制造商:Analog Devices 功能描述:EVAL BOARD - Bulk
EVAL-ADF4002EBZ1
功能描述:BOARD EVAL FOR ADF4002 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 主要目的:电源管理，电池充电器 嵌入式:否 已用 IC / 零件:MAX8903A 主要属性:1 芯锂离子电池 次要属性:状态 LED 已供物品:板
EVAL-ADF4007EBZ1
功能描述:BOARD EVALUATION FOR ADF4007EB1 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PSoC® 主要目的:电源管理，热管理 嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板，CD，电源